N5 / #5 Nylon Zipper Chain Production Set for Workshops – 200 m / 656.17 ft + 100 Single-Pull Sliders ST-T10T-NAYLON-200M100C

Production-level #5 zipper chain for variable product sizes

This N5 / #5 nylon zipper chain production set supplies 200 m / 656.17 ft of continuous zipper tape together with 100 single-pull sliders. It is intended for workshops that make bags, cases, organizers, pouches, textile covers and similar products in more than one size.

Continuous chain allows each zipper run to be prepared around the real opening of the finished item. This gives the workshop more flexibility than relying only on ready-made zipper lengths, especially when product designs include gussets, rounded corners, lining, binding or reinforced areas.

Measure the functional zipper path before cutting

Measure from the point where the zipper begins operating to the point where it needs to stop. Do not use the full outside perimeter of a bag or case unless that complete edge is the actual zipper route.

Include seam allowance, lining thickness, gusset depth, edge binding, zipper guards, corner turns and end finishing in the final measurement. For repair work, place the new zipper chain along the intended seam before cutting because older materials may have stretched, shifted or changed shape.

Why 200 meters is useful for ongoing workshop production

This quantity supports repeated production runs without requiring the workshop to stock many separate ready-length zippers. The final number of completed zipper runs depends on the length of each product opening, the number of sliders used per closure and the end-finishing method selected for the product.

Create a production list before cutting. Record each item’s zipper length, quantity, opening direction and slider requirement. This helps control tape consumption and prevents slider availability from becoming an afterthought once production is underway.

Single-pull sliders for one main access side

The included sliders have a single-pull configuration, meaning one pull tab is positioned on one side of the slider body. This works well for bag tops, case lids, organizer compartments and textile pouches normally opened from one main exterior face.

Single pull describes the pull-tab layout, not the direction of zipper travel. A product that must be operated comfortably from both sides may require another slider structure. Select the pull-tab configuration according to the actual way the completed item will be opened and used.

Check chain and slider compatibility before batch production

N5 / #5 is the intended size reference for this zipper-chain system, but size labels alone do not guarantee that every zipper construction will work with every slider. Nylon coil, molded plastic, metal teeth and different chain profiles can require different slider channels.

Before cutting multiple production lengths, test one included slider on a short sample of the exact chain. The slider should move smoothly, close the chain evenly and leave no visible gap behind it.

Before sewing the zipper chain

• Test one slider on a short section before cutting final production lengths.
• Keep both sides of the zipper tape parallel and evenly aligned during sewing.
• Allow clearance around lining, binding, gussets and reinforcement layers.
• Confirm the opening direction before attaching the chain to the product.
• Finish both zipper ends so the slider stays within the intended zipper route.

When another zipper construction may be more appropriate

This is an N5 / #5 nylon zipper-chain system. It may not be the right selection when the project requires molded plastic teeth, metal teeth, TPU-coated tape, a smaller zipper profile or a finished zipper with a specific end construction.

Choose the zipper around the product’s zipper channel, material thickness, expected opening frequency, load level and finished appearance. A zipper that looks similar can still be unsuitable when its chain profile or slider arrangement does not match the project.

Custom zipper requests

For custom zipper production, share the required chain length, zipper size, tape color, slider configuration, estimated quantity, intended product type and any sample or reference. This information helps determine the appropriate zipper-chain setup before production.

Frequently Asked Questions

Is this a ready-made zipper in one fixed length?

No. This is continuous N5 / #5 zipper chain. Each zipper run is cut to suit the finished product.

Are sliders included?

Yes. The set includes 100 single-pull sliders with 200 m / 656.17 ft of zipper chain.

What does single pull mean?

It means the slider has one pull tab on one side of its body. It does not mean the zipper can travel in only one direction.

Can this set be used for bags and cases?

It can be suitable when the zipper channel, material thickness, product structure and intended use are compatible with an N5 / #5 nylon zipper system.

Are end stops included?

The listed contents are zipper chain and sliders. The appropriate end finish should be chosen according to the final bag, case or cover construction.

Can I purchase tape separately for future production?

Yes. Workshops that want to plan tape and sliders independently can consider compatible N5 / #5 zipper-chain stock.