N3 / #3 Nylon Zipper Chain Set for Throw Pillow & Cushion Covers – 50 m / 164.04 ft + 100 Single-Pull Sliders ST-T5T-NAYLON-50M100K

Make each zipper fit the actual pillow-cover opening

Throw pillow covers, cushion covers and removable pillow covers are rarely made in one standard size. Piping, seam allowance, back openings, lining, envelope flaps and decorative construction can all change the usable zipper path.

This N3 / #3 nylon zipper chain set provides 50 m / 164.04 ft of continuous zipper tape and 100 single-pull sliders for workshops and makers producing more than a few covers at a time. It allows each zipper run to be prepared around the actual opening of the finished item instead of relying on the nearest ready-made zipper length.

Why a 50-meter zipper-chain set helps with repeat production

This quantity is designed for recurring home-textile work, not just one test cover. It can support multiple throw pillow styles, cushion-cover collections, replacement covers and small-batch upholstery or home-decor production.

The 100 included sliders should be planned together with the tape supply. A typical cover may use one slider, but the number of finished zipper runs depends on each cover’s opening length, the intended opening direction and the selected end-finishing method.

Measure the functional zipper path before cutting

Measure from the point where the zipper begins operating to the point where it needs to stop. Do not measure the entire perimeter of the cover unless that full edge will actually be used as the zipper route.

Allow for piping, seam allowance, zipper flaps, lining thickness, fabric bulk, corner turns and the end treatment. Before cutting a full batch, place the chain along the intended seam and test one slider on a short sample section.

Single-pull sliders for one main access side

The supplied sliders have a single-pull layout, with one pull tab on one side of the slider body. This can work well when a throw pillow or cushion cover is normally opened from the back panel or one main exterior face.

Single pull describes the location of the pull tab, not the direction of zipper movement. A design that must be opened comfortably from both sides may need a different slider configuration.

Check zipper-chain fit before sewing multiple covers

N3 / #3 identifies the intended zipper size for this chain-and-slider system. Before beginning a production batch, test one included slider on a short section of the exact chain.

The slider should move smoothly, close both sides evenly and leave no visible gap behind it. A similar-looking zipper may have a different coil shape, tape profile or slider channel, so avoid mixing components without a short compatibility test.

Choose the zipper construction around the cover design

This is a standard N3 / #3 nylon zipper-chain system. Where the closure must disappear completely into the seam, an invisible zipper may be a better design choice. For heavier textile covers or wider zipper channels, a larger zipper construction may be more suitable.

Choose the zipper around fabric thickness, closure position, expected use and the construction of the finished cover rather than appearance alone.

Custom zipper requests

For custom zipper supply, share the required chain length, tape color, slider layout, estimated quantity and a cover sample or drawing. These details help identify a zipper-chain arrangement that fits the finished home-textile product.

Frequently Asked Questions

Is this a finished zipper with ready-made ends?

No. This is continuous N3 / #3 zipper chain. The final length, slider installation and end finish are prepared by the workshop or maker.

Are sliders included in the set?

Yes. The set includes 100 single-pull sliders with 50 m / 164.04 ft of zipper chain.

Can I cut the tape for different pillow-cover sizes?

Yes. The chain is intended to be cut around the actual working opening of each pillow or cushion cover.

What does single pull mean?

It means the slider has one pull tab on one side of its body. It does not mean the zipper moves in only one direction.

Can this set be used for cushion-cover repairs?

It can be suitable where the existing zipper profile, sewing construction and required opening are compatible with N3 / #3 nylon zipper chain.

Does the set include end stops?

The listed contents are zipper chain and sliders. The end-finishing method should be chosen according to the final cover design.